光伏發電坑人？在這個光伏普及的時代，這樣的質疑未必無因。光伏發電系統的組成部分眾多，其中的哪一點出了問題，都可能影響整體效率，從而導致收益降低。那么到底光伏發電怎么樣才是坑人呢？如何規避？以下是五個常見的“坑人”之處。

一、光伏支架

光伏支架是光伏電站系統中為了擺放、安裝、固定光伏電池板而設計的特殊的支架。設計不充分的支架遇到強風時，容易發生支架傾覆、組件散落損毀。

好的支架鋼結構厚度符合標準要求 ，熱鍍鋅材料或者優質鋁合金材料，基本厚度等于或大于2.2mm，抗腐蝕性和抗風性能強，也能保證25年的使用壽命。而便宜的支架可能連2mm厚度都沒有，抗腐蝕性和抗風性能差，且光伏系統常年在外風吹日曬，支架腐蝕造成光伏組件墜落，將得不償失;即使組件沒掉，但腐蝕的支架會造成組件傾角發生變化，減少系統發電量，從而導致收益受損。

二、光伏電纜

光伏線纜需有耐氣候、耐高溫、耐摩擦等特性，并且具有超長的使用壽命。光伏線纜因其特殊性能成本很高，若選擇普通線纜來替代，這種線纜用在光伏系統中保護層兩三年就腐蝕了，導致線纜內部銅絲暴露，很容易造成漏電，甚至引發火災。

三、光伏組件

光伏組件是光伏發電系統中的核心部分，光伏組件的質量好壞直接影響了使用壽命的長短和收益的高低。差的背板材料耐候性差，直接影響組件的使用壽命。如邊框材料強度不夠，可能直接造成光伏板陣在強風時邊框脫落或撕裂。

如何識別電站組件好壞：

首先，要看組件的供應商 ，是不是行業主流品牌，一般大品牌的質保和售后服務是有保障的。其次，看電池片串焊的時候有沒有漏焊，還有背面承壓的質量 ，承壓有沒有不平整的情況，或是氣泡，褶皺等。以及邊框質量，是不是嚴格成矩形，誤差不能太大。

四、光伏逆變器

逆變器是將直流電能變換成交流電能的中介。逆變器的質量好壞決定了電能轉換效率的高低。逆變器是光伏系統中較容易出現問題的設備之一，一定要購買正規廠家的優質產品，才能確保穩定長期發電 。日常維護也要注意通風散熱，避免潮濕和過于封閉的環境。品質好、效率高的逆變器可以使光伏系統的發電量更高，像這種一線逆變器品牌轉換效率都在98%以上;而品質不好、效率低的逆變器則會減損系統發電量，這些逆變器轉換效率大多只有95%甚至更低。

五、光伏并網箱

好的并網箱比質量不好的可能貴到500塊錢一臺。但兩者有什么差別呢?好的并網箱能保證產品符合電網要求，而質量不好的并網箱，可能沒有檢有壓合閘和欠失壓脫扣功能或者質量差失靈，這會造成反送電——即電網停電的情況下，萬一逆變器質量也不好，光伏系統仍然帶電工作，就有可能造成光伏系統的電反送給電網，萬一此時電網上有工作人員在檢修，則可能造成觸電事故，嚴重的造成人員傷亡。

其次是電器質量差，失火、損毀現象多，安全風險大。并網計量配電箱內必須有市電和光伏發電隔離開關(閘刀開關)、(自復式)過欠壓保護器、浪涌保護器(避雷器)、漏電保護開關(負荷開關)、接地裝置。

判斷光伏系統的優劣：

第一，對系統外觀進行檢查，如組件、陣列、并網箱等，如發現問題、組件損壞、遮擋、灰塵等，可以采取相應措施及時解決;

第二，檢查電站建設承包單位采用的系統部件是否具備質量認證證書。

第三，要求對系統的安全性進行現場測試，如接地連續性、絕緣性、是否具有防雷設置等，如有問題，應讓電站建設單位及時解決。

無論是夸夸其談還是樸實無華，事關收益與安全，根本上還是光伏電站的質量問題，把控好這一點，便可在本質上規避坑人之局。

Photovoltaic power pit people? In this era of photovoltaic popularization, such doubts may not be without cause. There are many components of a photovoltaic power generation system, and any one of them that goes wrong can affect the overall efficiency, resulting in lower revenues. So how is photovoltaic power generation a pit man? How to circumvent? Here are five common "pit people" points. First, photovoltaic bracket
Photovoltaic bracket is a special bracket designed for placement, installation and fixing of photovoltaic panels in photovoltaic power plant systems. When the bracket with insufficient design encounters strong wind, it is easy to overturn the bracket and scatter and damage the components.

Good bracket steel structure thickness meets the standard requirements, hot-dip galvanized material or high-quality aluminum alloy material, the basic thickness is equal to or greater than 2.2mm, strong corrosion resistance and wind resistance, but also can ensure a service life of 25 years. The cheap bracket may not even have a thickness of 2mm, poor corrosion resistance and wind resistance, and the photovoltaic system is exposed to the wind and sun outside all year round, and the corrosion of the bracket causes the photovoltaic module to fall, which will not be worth the loss; Even if the component is not lost, the corroded bracket can cause the inclination of the module to change, reducing the power generated by the system, resulting in lost revenue.

Second, photovoltaic cable
Photovoltaic cables need to have weather, high temperature, friction and other characteristics, and have a long service life. Photovoltaic cable because of its special performance cost is very high, if you choose ordinary cable to replace, this cable is used in the photovoltaic system protective layer for two or three years corroded, resulting in the internal copper wire of the cable is exposed, it is easy to cause leakage, and even cause fire.

Third, photovoltaic modules
PV modules are the core part of the photovoltaic power generation system, and the quality of PV modules directly affects the length of service life and the level of income. Poor backsheet material has poor weather resistance, which directly affects the service life of the component. If the strength of the frame material is not enough, it may directly cause the frame to fall off or tear when the photovoltaic panel array is strong wind.

How to identify the quality of power station components:
First of all, it depends on the supplier of the component, whether it is a mainstream brand in the industry, and the warranty and after-sales service of the general big brand are guaranteed. Secondly, look at whether there is leakage welding during the string welding of the battery sheet, as well as the quality of the pressure on the back, whether there is unevenness in the pressure, or bubbles, folds, etc. As well as the quality of the border, whether it is strictly rectangular, the error cannot be too large.

Fourth, photovoltaic inverter

The inverter is the intermediary that converts DC energy into AC energy. The quality of the inverter determines the efficiency of power conversion. The inverter is one of the more problematic equipment in the photovoltaic system, and it is necessary to purchase high-quality products from regular manufacturers to ensure stable long-term power generation. Daily maintenance should also pay attention to ventilation and heat dissipation, avoid humidity and too closed environment. Inverters with good quality and high efficiency can make the power generation of the photovoltaic system higher, and the conversion efficiency of first-line inverter brands like this is more than 98%; Inverters with poor quality and low efficiency will reduce the power generation of the system, and most of these inverters have a conversion efficiency of only 95% or even lower.

5. Photovoltaic grid-connected box
A good grid-connected box may be as expensive as 500 yuan a piece than a poor quality box. But what's the difference? A good grid-connected box can ensure that the product meets the requirements of the power grid, and the poor quality grid-connected box, may not have a pressure closing and under-voltage trip function or poor quality failure, which will cause reverse transmission - that is, in the case of power grid failure, in case the quality of the inverter is not good, the photovoltaic system is still live work, it may cause the photovoltaic system to be sent back to the grid, in case there are staff on the power grid at this time, it may cause electric shock accidents, serious casualties.

Secondly, the quality of electrical appliances is poor, there are many fires and damages, and the safety risks are large. There must be mains and photovoltaic power generation disconnectors (gate switches), (self-restorative) over-undervoltage protectors, surge protectors (lightning arresters), leakage protection switches (load switches), and grounding devices in the grid-connected metering distribution box.

Judge the advantages and disadvantages of photovoltaic systems:
First, check the appearance of the system, such as components, arrays, grid-connected boxes, etc., such as finding problems, component damage, occlusion, dust, etc., you can take corresponding measures to solve them in time;

Second, check whether the system components used by the power station construction contractor have quality certification certificates.

Third, it is required to conduct on-site tests on the safety of the system, such as grounding continuity, insulation, whether it has lightning protection settings, etc., if there is a problem, the power station construction unit should be allowed to solve it in time.

Whether it is rhetoric or unpretentious, it is related to income and safety, and it is fundamentally a quality problem of photovoltaic power plants, and controlling this can essentially avoid the situation of pit people.